Title: Test Indicators Quiz
Course: 15/FA Tools, Instruments & Machines (MCHT-1630-01) > Section: Learning Modules

The post-quiz for WXMT204-XX01XEN-E1 - Test Indicators.

Q: An indicator will have cosine error when which of the following is not aligned correctly?
- Body
- Contact tip
- Primary needle
- Secondary dial
A: Contact tip
If wrong: Review Chapter 1 - Test Indicators.

Q: An indicator with hysteresis error will show the same amount of needle movement when measuring a workpiece regardless of the direction of the needle. Is this statement TRUE or FALSE?
- True
- False
A: False
If wrong: Review Chapter 1 - Test Indicators.

Q: An indicator with the contact tip set at the wrong angle will produce a reading __________ the actual dimension.
- less than
- greater than
- twice
- the same as
A: greater than
If wrong: Review Chapter 1 - Test Indicators.

Q: Another name for the secondary dial is the __________.
- multiplier
- Primary needle
- revolution counter
- measuring scale
A: revolution counter
If wrong: Review Chapter 1 - Test Indicators.

Q: Each graduation mark on the indicator face is equal to which of the following?
- range
- resolution
- Measurement scale
- 1 mm
A: resolution
If wrong: Review Chapter 1 - Test Indicators.

Q: For most test indicators, at what angle should the contact tip be set in relation to the work surface?
- 0 degrees
- 45 degrees
- 90 degrees
- Any angle
A: 0 degrees
If wrong: Review Chapter 1 - Test Indicators.

Q: Test indicators can't be used to measure flatness. Is this statement TRUE or FALSE?
- True
- False
A: False
If wrong: Review Chapter 1 - Test Indicators.

Q: The abbreviation F.I.M. stands for which of the following?
- Fixed Indicated Motion
- Full Involute Motion
- Full Indicator Movement
- Fried In Margarine
A: Full Indicator Movement
If wrong: Review Chapter 1 - Test Indicators.

Q: The abbreviation T.I.R.. stands for which of the following?
- Total Involuntary Recall
- Total Indicator Reading
- Total Indicator Range
- Temporary Indicator Resolution
A: Total Indicator Reading
If wrong: Review Chapter 1 - Test Indicators.

Q: The contact tip should move in which direction in relation to the work surface?
- parallel
- perpendicular
- At 45 degrees
- At any angle
A: perpendicular
If wrong: Review Chapter 1 - Test Indicators.

Q: The indicator range is which of the following?
- Largest distance you can accurately measure
- Smallest distance you can accurately measure
- Distance between two graduation marks
- Temperature within which the indicator is accurate
A: Largest distance you can accurately measure
If wrong: Review Chapter 1 - Test Indicators.

Q: The smallest distance a test indicator can accurately measure is which of the following?
- range
- resolution
- 1 inch
- 1 mm
A: resolution
If wrong: Review Chapter 1 - Test Indicators.

Q: What is the acceptable error when setting the contact tip angle from its correct angle?
- 45 degrees
- 30 degrees
- 15 degrees
- 7 degrees
A: 7 degrees
If wrong: Review Chapter 1 - Test Indicators.

Q: What is the F.I.M. reading of the measurement shown in the animation?
- -.003
- .009
- .012
- .060
A: .012
If wrong: Review Chapter 1 - Test Indicators.

Q: What is the range of the indicator shown?
- .001
- .010
- .030
- .100
A: .010
If wrong: Review Chapter 1 - Test Indicators.

Q: What is the resolution of the indicator shown?
- .0001
- .0005
- .030
- 1 inch
A: .0005
If wrong: Review Chapter 1 - Test Indicators.

Q: What is the T.I.R. reading of the measurement shown in the animation?
- .0
- .0005
- -0.001
- .009
A: .009
If wrong: Review Chapter 1 - Test Indicators.

Q: When the contact tip is at the correct angle, the body should be at which of the following angles?
- 45 degrees
- 30 degrees
- 15 degrees
- Any angle
A: Any angle
If wrong: Review Chapter 1 - Test Indicators.

Q: Which of the drawings shows a contact tip in the correct position to measure a round workpiece?
- A
- B
- C
- D
A: A
If wrong: Review Chapter 1 - Test Indicators.

Q: Which part of the test indicator should contact the surface to be measured?
- Contact tip shaft
- Contact tip ball
- Body
- needle
A: Contact tip ball
If wrong: Review Chapter 1 - Test Indicators.

Q: Which test indicator component allows you to rotate the indicator face?
- Primary needle
- Body
- bezel
- Contact tip
A: bezel
If wrong: Review Chapter 1 - Test Indicators.